SKU: 61793655932

S&B Filters CAI-DD64-18-1 JLT Cold Air Intake Kit 2021 Dodge Durango SRT 6.4L No Tuning Required SB

$157.05 $174.50
Save 10%
No.2 Bestseller on sm10m.ch >

Pay in installments of $43.62 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 11 - Aug 16

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

S&B Filters CAI-DD64-18-1 JLT Cold Air Intake Kit 2021 Dodge Durango SRT 6.4L No Tuning Required SBJLT Cold Air Intake For 2021 Durango SRT 6. 4L Help your HEMI get all the cold air it can eat! Looks great, sounds great with No Tune Required This Kit Includes a roto molded Heat Shield that has a opening in the front to grab fresh air from the grille headlight area and also seals to the hood. Our air filter is a custom built design made by SB. It has a built in bell mouth for super smooth and fast air flow as well as huge 1 inch deep pleats for more

JLT Cold Air Intake For 2021 Durango SRT 6.4L Help your HEMI get all the cold air it can eat! Looks great, sounds great with No Tune Required

This Kit Includes a roto molded Heat Shield that has a opening in the front to grab fresh air from the grille/headlight area and also seals to the hood.

Our air filter is a custom built design made by SB. It has a built in bell mouth for super smooth and fast air flow as well as huge 1 inch deep pleats for more surface area than filters that look much bigger.

The intake tube is roto molded plastic with a huge 5 inch filer opening for superior airflow and No heat soak like metal tubes.
With a mouth of 4 inch at the throttle body end, it is ready for any larger throttle bodies that may come in the future.

Finish
Standard Finish is an OEM looking black textured plastic.

Heat Shield
Includes our large ABS plastic Heat Shield to block engine heat at idle and low speed.
It uses a large area to make sure the filter has tons of cool air and uses the factory fresh air inlet from the bumper to keep temps cool as stock

Kit Includes:

  • JLT Roto Molded Plastic Intake Tube
  • Silicone Reducer
  • 5x7 SB Powerstack Air Filter Red Oil
  • JLT Roto Molded Heat Shield with fresh air feed
  • HD Clamps, all needed hardware

Gains and Testing
18-22 RWHP and 18-22 RWTQ are typical with this kit.

Tuning
No Tuning Required

THIS KIT IS NOT 50 STATE STREET LEGAL.

Easy Install
The design, detailed instructions and online video helps make this an

JLT Pre-Filtersare now available for most intake kits we carry, these filters are made for us by Outerwears, these prefilters are water repellent. They will increase your filter life and cut down on your cleaning intervals!

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 61793655932

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.5 ★★★★★
Based on 13 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
C
Verified Purchase
CinemaPete
Battle Creek, US
★★★★★ 5
Excellent Tool For Drilling Shelf Pin Holes
I had a project where I was extending the depth of the bottom half of a bookcase I had made out of pre-drilled MDF from Home Depot. The original bookcase was 11" deep x 10' high. The extended depth of the bottom is to be used to hold audio gear and needed to be 18" depth, front to rear. I was able to increase the depth but had to insert additional panels on the left and right so that shelf pins could be installed. I needed a shelf pin jig to do that, and this jig was perfect for the job. After completing my holes and mounting some shelves I was pleased that the alignment with the inner portion of the shelf was perfect and the distance between holes lined up exactly as with the original panels from Home Depot. The jig is high quality fabricated aluminum, not plastic, and it comes with two drill bits, and stop and Allen wrench, including an instruction manual, all in an attractive plastic case. The jig is well worth the modest price and I would definitely recommend it for drilling shelf clip holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 27, 2024
T
Verified Purchase
To Protect the Innocent
West Palm Beach, US
★★★★★ 5
a solid choice
I realized I don't need to drill 5mm holes, so this item is just perfect. It's higher quality than those other cheap-chinese noname jigs. In particular: * The stop collar provided actually fits the drill bit. I had one from Tanyo that had too-big collars that didn't stay put. * The fence pins are very soilid, so the jig doesn't move while in place. Other brands have a long knurled screw that wobbles and allows the kiig to move around. * The plate is thick, making it feel sturdy. * It's phyically smaller than the others, because it doesn't have any useless features like euro-hinge hole guides. The case is more compact and stores well. Overall, very satisfied with this jig.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 3, 2026
E
Verified Purchase
ed
Waukegan, US
★★★★★ 5
Great product
Great well made product and nice case. Works great for 1/4” holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 15, 2026
L
Verified Purchase
Lori Cook
Waukegan, US
★★★★★ 5
A solid and easy to use product.
Worked like a charm. It is extremely durable and easy to use. I bought this item because the one I wanted wasn’t available. I don’t regret getting it.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 22, 2026
B
Verified Purchase
Bill
Fort Morgan, US
★★★★★ 5
very nice tool
likes, all aluminum construction, seems very accurate and uses more sturdy 1/4 inch shelf pins instead of the 5mm ones comes with 2 bits which is a huge plus the competition makes you buy the 1/4 drill and only is set up for 5mm to start. this jig will work along side, for now, my other jig dislike is the fact it only has 1/4 pin capability not a deal killer in any way, and it has "pins" to support the jig on the edge again this is both an advantage and disadvantage as you can change the depth of where the pins are located BUT if you are making something smaller the jig may not calibrate consistently. on another positive you can replace the bits easily and commonly as they are not proprietary and simply standard 1/4 inch bits this will be a fine addition to my other goingmake tools and future ones
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 3, 2025

recommand products

Ezri Sideboard
1949.50
Placuna Pendant
179.00
Hand Carved 4 Door Sideboard
754.00
Abaso Sideboard
2299.50
Cortado Table Lamp
209.00