Pay in installments of $62.75 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Sep 6 - Sep 11
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Reci W4 S4 Z4 100W Max.130W CO2 Laser Tube Wooden Case Box Packing Length 1400 Dia. 80mm for CO2 Laser Engraving Cutting MachineReci W4 S4 Z4 100W Max. 130W CO2 Laser Tube Wooden Case Box Packing Length 1400 Dia. 80mm for CO2 Laser Engraving Cutting Machine Product Description Mark & Model: W4, The product is featured as small size and good model, higher power rate compared with the laser tube of similar length and longer service time, which is suitable for laser marking, laser cutting and laser engraving. 1. Installation Requirement: Make sure to follow the operation
Reci W4 S4 Z4 100W Max.130W CO2 Laser Tube Wooden Case Box Packing Length 1400 Dia. 80mm for CO2 Laser Engraving Cutting Machine
Mark & Model: W4, The product is featured as small size and good model, higher power rate compared with the laser tube of similar
length and longer service time, which is suitable for laser marking, laser cutting and laser engraving.
1. Installation Requirement:
Make sure to follow the operation instruction of model W4 as shown in the illustration. The dedicated power P14 should be
equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 24kv). It may cause the following
consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause
water leakage.
2. Operation conditions:
Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10鈩�-40鈩�.
The operating environment: temperature 2-40鈩�; Humidity 10-60%.
The working current: test current is 30mA. Maximum working current is 30mA. The running current must be kept below 28mA. The life
span can reach 10,000 hours if the current is kept below 26mA. The ammeter must be connected to the negative electrode of laser
tube.
When it is working under over-high current for long term, the negative pole will appear light yellow and the life span will be
shortened rapidly.
To protect dust from going into the insulation sheath, please wrap it with plastic film.
3. Working Performance:
Cutting function.
Engraving function: Very good. When the working current is 4mA and the tube is in the state of preionization, the laser can be
used for high-frequency impulse engraving.
4. Key Notes:
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be
seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideways with an air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean
the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.
Attention: it is forbidden to clean the mirror with acetone.
The screws in the front and back ends of the laser tube are not allowed to be moved, otherwise the output power will be declined,
even the tube will be scrapped.
Put the acryl 300mm far away from output mirror, when testing its laser spot.
5. Safety:
The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage.
Pay attention to the security marks.
6. Storage and Transportation Requirement:
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag.
The storage environment is 2-40鈩�, and the requested humidity is 10-60%. Pack the laser as in the original way.
Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from
vertically sliding during transportation. The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the
side of reflecting mirror must be 50 mm wider.
7. Tubes operated in wrong way are not guaranteed by Manufacturer.
length and longer service time, which is suitable for laser marking, laser cutting and laser engraving.
1. Installation Requirement:
Make sure to follow the operation instruction of model W4 as shown in the illustration. The dedicated power P14 should be
equipped. The positive pole of laser tube is in high voltage (the ignition voltage is 24kv). It may cause the following
consequence when it is failed to follow the instruction: Arcing; the inner tube will be punctured by electricity and may cause
water leakage.
2. Operation conditions:
Water cooling: using purified water; 3 to 5 liter/minute; water temperature: 10鈩�-40鈩�.
The operating environment: temperature 2-40鈩�; Humidity 10-60%.
The working current: test current is 30mA. Maximum working current is 30mA. The running current must be kept below 28mA. The life
span can reach 10,000 hours if the current is kept below 26mA. The ammeter must be connected to the negative electrode of laser
tube.
When it is working under over-high current for long term, the negative pole will appear light yellow and the life span will be
shortened rapidly.
To protect dust from going into the insulation sheath, please wrap it with plastic film.
3. Working Performance:
Cutting function.
Engraving function: Very good. When the working current is 4mA and the tube is in the state of preionization, the laser can be
used for high-frequency impulse engraving.
4. Key Notes:
Do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be
seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideways with an air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean
the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.
Attention: it is forbidden to clean the mirror with acetone.
The screws in the front and back ends of the laser tube are not allowed to be moved, otherwise the output power will be declined,
even the tube will be scrapped.
Put the acryl 300mm far away from output mirror, when testing its laser spot.
5. Safety:
The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage.
Pay attention to the security marks.
6. Storage and Transportation Requirement:
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag.
The storage environment is 2-40鈩�, and the requested humidity is 10-60%. Pack the laser as in the original way.
Important notes: it is requested to use adhesive tape to cement the sponge together with laser tube to prevent the tube from
vertically sliding during transportation. The sponge in the side of output mirror must be 70 mm beyond it, and the sponge in the
side of reflecting mirror must be 50 mm wider.
7. Tubes operated in wrong way are not guaranteed by Manufacturer.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.6 ★★★★★
Based on 25 reviews
Sort
Product Reviews
★★★★★ 5
Best Vitamins
I started using Pure Vitamins when I was going to a weight loss clinic and was so happy to find them on here. Great product!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 25, 2026
★★★★★ 5
Like this product
Easy to swallow tablets and good value
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
★★★★★ 5
Great product
Excellent product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 25, 2026
★★★★★ 5
Important supplement for osteo issues
Nutritionist recommended quality brand is a good way to get calcium supplement. Easy to swallow capsules have no after-taste.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 30, 2026
★★★★★ 4
Good supplement
In order to get the recommended dose, you need to take a lot of these in a day. However, they are easy to swallow and I trust this brand. If you're looking for a good calcium supplement, this is a good one.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 29, 2023
recommand products
Best Father Since 2016 v3 - Luxury Dog Tag Necklace
39.95
Best Father Since 1992 v3 - Luxury Dog Tag Necklace
39.95
Best Father Since 1975 v2 - Luxury Dog Tag Necklace
39.95
Nakamichi Wireless Apple CarPlay & Android Auto Solution for Toyota Prado 2014-2017
599.50
Best Father Since 1989 v3 - Luxury Dog Tag Necklace
39.95