JBL MARINE A1000 1000 Watts Subwoofer Marine Amplifier

JBL MARINE A1000 1000 Watts Subwoofer Marine AmplifierThe JBL marine A1000 mono subwoofer amplifier delivers 1000 Watts RMS using a Class D amplifier design to ensure high output and minimum current draw. Speaker level inputs allow this amplifier to integrate into almost any system, even one using your marines factory radio. You can use the low pass filter and variable bass boost to maximize the performance of your subwoofer and enclosure, while a phase switch ensures that the bass will blend well with

The JBL marine A1000 mono subwoofer amplifier delivers 1000-Watts RMS using a Class D amplifier design to ensure high output and minimum current draw. Speaker-level inputs allow this amplifier to integrate into almost any system, even one using your marine’s factory radio. You can use the low-pass filter and variable bass boost to maximize the performance of your subwoofer and enclosure, while a phase switch ensures that the bass will blend well with your full-range speakers.

Compact size
The JBL marine amplifier features a low-profile chassis and a small overall footprint to fit in more vehicles where available space is limited.

High and low level input
Speaker-level and low-level inputs allow the marine to integrate with both aftermarket and factory marine stereo systems.

Variable crossover and bass boost
Unlike many amplifiers available at similar prices, the JBL marine amplifier features variable electronic crossovers and bass boost circuits allowing for precise system tuning and performance. 

Low noise and distortion
The marine amplifier has been engineered using Balanced Differential Inputs to ensure low noise and distortion even at high output levels. This also makes it far less susceptible to line induced radiated engine noise. 

Input level control
When low-level inputs are used, this control adjusts the input sensitivity between 200mVrms and 4Vrms. When high-level inputs are used, this control adjusts the input sensitivity between 1Vrms and 22Vrms.

Full on-board protection
On-board circuitry protects the marine amplifier from shorts, high-temperature, overvoltage and undervoltage. An LED indicator is provided to let you know when one of these conditions exists.

Phase switch
This switch changes the input phase to inverted or non-inverted. This is especially helpful as part of system tuning based on the enclosure type and location in the boat.

RBC wired remote
The RBC wired remote is an easy installation and can be mounted for convenient volume adjustment from driver’s seat.

Strappable for up to 2000 watts of power at 4 ohms
Enable to strap two marine A1000 together to double your power, The Primary amp will be in absolute control of Secondary in terms of the crossover points, the gain and remote level control.

Class D amp technology
The JBL marine mono subwoofer amplifier delivers 600-Watts RMS using a Class D amplifier design to ensure high output and minimum current draw.

Turn-on mode
This switch changes DC to REM to adapt with low-level signals or high-level signals, this is especially helpful as part of remote turn-on lead of your installation more choice .A selectable “Turn-on mode” can protect battery to avoid current drain, when you don’t expect turn on your amplifier

Specifications

• mono subwoofer marine amplifier
• 600 watts RMS x 1 at 4 ohms (1000 watts RMS x 1 at 2 ohms) Max power 2000 watts
• 1900 watts RMSx1 (Two amplifiers)
• Class D amp technology
• frequency response: 25-320 Hz
• variable low-pass filter (32-320 Hz, 12 dB/octave)
• variable bass boost (0-12dB at 45Hz)
• phase switch (0, 180 degrees)
• wired remote level control included
• preamp inputs and outputs
• speaker-level inputs (speaker wire-toRCA adapters included)
• 4-gauge power and ground leads recommended — wiring and hardware not included with amplifier
• fuse rating: 35A x 3
• WxHxD=320mm x 51.3mm x 180mm WxHxD=12-5/8” x 2-1/16” x7-1/8”