Pay in installments of $84.50 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Sep 24 - Sep 29
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
For Small Block Ford 6.56-Inch 12-1X Crank Kit, Sbf, Hall Effect-556-172Upgrading to an MSD Flying Magnet Crank Kit will deliver the precise and reliable signal that a high performance engine requires. This kit gives you the ability to control timing electronically through a Holley EFI ECU (or other standalone engine management system ignition controller). At the heart of the kit is the 3 wire Hall Effect Sensor that is easier to set up, less susceptible to EMI RFI interference noise, and less likely to have false signals
Upgrading to an MSD Flying Magnet Crank Kit will deliver the precise and reliable signal that a high performance engine requires. This kit gives you the ability to control timing electronically through a Holley EFI ECU (or other standalone engine management system / ignition controller). At the heart of the kit is the 3-wire Hall-Effect Sensor that is easier to set up, less susceptible to EMI/RFI interference/noise, and less likely to have false signals than other methods (Distributors and VR Magnetic Sensors). In addition, they are less prone to mechanical failure since there are no wear parts. With the included high quality timing pointer and the use of a direct bolt-on, degreed balancer (see below list for recommendations), you'll be able to adjust timing in the precise increments required for your engine. • Coyote 556-173 We recommend using ATI 918047-MSD but will also work with 918047N and 918047NA • LS 8 inch 556-174 Designed to work directly with ATI 917302, 918852, 917264 or 917242 • LS 7.28 inch 556-175 Designed to work directly with ATI 917777, 917211 or 917234 • LS 6.56 inch 556-176 Designed to work directly with ATI 917776 or 917215
Features:
- Most accurate way to your electronic fuel injection (EFI), can be installed as 12-1 or 12x
- Powerful magnets embedded in a 3/8-inch thick billet 6061-T6 aluminum wheel
- 3-wire Hall-Effect Sensor that is not easily susceptible to EMI/RFI Interference
- Engine specific kits include a direct bolt-on billet aluminum pick up bracket
- Rigid mounting that will not flex and cause timing fluctuation
- Easy to install much like traditional MSD Crank Kits
- Included installation instructions cover mechanical setup and provide step-by-step Holley EFI Software Setup
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.9 ★★★★★
Based on 26 reviews
Sort
Product Reviews
★★★★★ 5
Amazing MagSafe phone stand
I recently purchased this MagSafe car phone mount, and it has been a game-changer for my daily commutes. The installation was effortless—just snap it onto the air vent, and you’re good to go.
What stands out the most is the strong MagSafe connection. My phone stays securely in place even on bumpy roads, and removing it is just as seamless. The minimalist design fits perfectly with my car’s interior, and it doesn’t block my view like other bulkier mounts.
Another highlight is the 360-degree rotation feature, which makes adjusting the angle for navigation or hands-free calls incredibly easy. It’s sturdy, reliable, and eliminates the need for clamps or adhesives.
Overall, this is a must-have for anyone who uses their phone for GPS or music while driving. Highly recommended for MagSafe-compatible phones!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 30, 2024
★★★★★ 5
Great Phone Mount
This is a great little phone mount! Simple and effective. I’ve been wanting something for when I am pulled over at a super charger to be on a call or watching something on my phone without holding it or putting it in the cup holder. Works super well with my MagSafe case although it does come with extra magnets as well in case you don’t have a MagSafe case. Highly recommend! Easily attaches to the screen, no sticky residue or risk of sun staining on the dash like other mounts.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on July 2, 2025
★★★★★ 5
Best one so far!
This is a great device! Not my first one but definitely better than I had before! It mounts on the side of the screen, which is very convenient as my other one was sticky, so I had to leave it with my other car. The handles rotate well to give you any position that suits you. There is some good suction, so it sticks well and doesn’t fall. It’s good quality and sturdy. The phone magnets very well to it and also doesn’t fall. I rotate it any way I want but mostly vertically and diagonally. I had it for a while now so can give you my honest opinion. Highly recommend!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 30, 2025
★★★★★ 5
Recommend
Color: Black
This a great little phone mount. It works for my iPhone 17 pro max. I drive a lot of dirt roads where I live in the mountains, and the magnet holds up to plenty of bumps without dropping my phone. Easy to install.
Pros:
-very simple installation
-strong magnet
-arm rotates for adjustment
-ball and socket joint allows tilting with a good amount of resistance to hold its position (when fully tightened)
Cons:
- for model 3 users, anything other than next to the steering wheel can block a portion of your windshield viewing area
-could have more modularity if offered with more arm attachments
Conclusion:
RECOMMENDED. Very stable and functional mount with a minimalistic design that still allows for some adjustability.
If magnet weakens over time, or the sun damages the plastic to the point of breaking from brittleness then I will post updates. I will also update for any modifications I make for more adjustability.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 26, 2026
★★★★★ 5
This economical solution works perfectly
Color: Black
Very happy with this car mount. The magnet is plenty strong to securely hold my iPhone in its magnetic loop case. It’s plastic but it’s sturdy and fits on my Model 3’s screen perfectly. It has an adjustable height that I can mount my phone with full clearance of my steering wheel.
Don’t waste your money on a metal mount, this inexpensive mount serves the need perfectly.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 22, 2026